Lem PCB - Panduan Komprehensif untuk Perekatan dalam Pembuatan dan Perbaikan PCB

Lem PCB - Panduan Komprehensif untuk Perekatan dalam Pembuatan dan Perbaikan PCB

Gluing components onto printed circuit boards securely is crucial for product durability. The right adhesive choice and application technique make the difference between PCB assemblies that fail at the slightest vibration or thermal cycle versus those able to withstand years of rugged use.

This comprehensive guide covers the types of PCB glues available, their properties, usage recommendations, and methods for proper application and removal to aid PCB assembly and repair.

Daftar Isi
    Menambahkan tajuk untuk mulai membuat daftar isi

    Apa itu Lem PCB?

    PCB Glue
    PCB Glue

    Lem PCB mengacu pada perekat yang diformulasikan untuk merekatkan komponen dan bahan secara permanen atau sementara ke papan sirkuit tercetak. Lem ini menggantikan atau menambah penyolderan tradisional untuk memasang komponen SMD seperti kapasitor, konektor, dan sirkuit terpadu ke substrat PCB.

    Key properties sought in PCB glues include:

    ●Strong adhesive bond strength to maintain robust component attachment

    ●Suitable viscosity and curing characteristics for assembly processes

    ●Excellent electrical insulation to avoid short circuits

    ●Resistance to temperature cycles, humidity, and chemicals

    ●Non-conductivity to prevent electrical issues

    Proses perekatan lem pada produksi PCB

    Lem Apa yang Digunakan pada Papan PCB?

    There are several major types of glue used on PCB boards for component attachment and general bonding applications:

    Cyanoacrylate
    Fast-curing cyanoacrylate adhesive provides high strength with low viscosity for wicking into joints. Bonds most plastics. Industrial grades withstand high temperatures.

    Epoksi
    Two-part epoxies cure at room temperature into rigid, durable bonds. Different resins/hardeners provide properties from flexible to heat-resistant.

    Silikon
    Silicone adhesive/sealant remains flexible after curing. Withstands high temperatures while insulating electricity. Used for potting and protective coatings.

    Lem Panas Meleleh
    Thermoplastic hot melt glues provide quick adhesion. Mostly used for temporary holding during assembly rather than permanent bonds.

    Perekat Penyembuhan UV
    Liquid adhesives cure rapidly under UV irradiation. Low curing stresses make them suitable for bonding sensitive components.

    Each glue type has characteristics that make it suitable for certain PCB applications, components, and operating conditions. Selecting the optimal match maximizes robustness.

    Which Glue is Best for Electronics?

    Which Glue is Best for Electronics
    Which Glue is Best for Electronics

    For bonding electronics components, the best glue for electronics depends on the materials being joined and operating environment:

    ●Cyanoacrylate provides fast room temperature cure with low viscosity suitable for bonds with small clearances like SMT components. Industrial grades withstand soldering temps.

    ●Epoxy forms rigid, creep-resistant bonds between a wide range of materials including metals, plastics, and ceramics. Withstands vibration and is electrically insulating.

    ●Silicone excels for high temperature electronics bonding. Flexible bonds tolerate thermal cycling and high voltage insulation. Useful for component potting and coating PCBs.

    ●UV cure adhesives work well for glass bonding on displays and optical components. Cure quickly with low stress and shrinkage.

    ●Hot melt glue serves for temporary holding during PCB assembly when rapid tacking is needed prior to soldering. Not suitable for permanent bonds.

    The best electronics glue depends on operating temperature range, materials, strength needs, temporary vs permanent usage, and application method.

    What is the Non-Conductive Glue for PCBs?

    Preventing short circuits makes selecting a non-conductive PCB glue essential. The following are inherently electrically insulating options:

    Epoksi– Composite epoxy resins filled with glass or ceramic reliably maintain high resistivity ideal for insulating closely spaced PCB traces. Withstands flux and cleaning.

    Silikon– Silicone remains stable from -45 to 200°C. Different silicone types optimize flexibility, adhesion, and dielectric strength as needed.

    UV Cure – Acrylic, epoxy, and silicone-based UV cure adhesives transmit no conductivity after curing under ultraviolet light.

    Hot Melt – Thermoplastic hot melt glues are electrically insulating in their fully solidified state. Allow sufficient cool-down after application.

    Cyanoacrylate– Industrial cyanoacrylate grades with thickening agents help insulate contacts from stray conductivity during cure.

    Applying non-conductive PCB glue between solder joints, exposed contacts, and other close conductive surfaces prevents arcs, leakage current, and shorting failures.

    Apa Lem Terbaik untuk Perbaikan PCB?

    What is the Best Glue for PCB Repair
    What is the Best Glue for PCB Repair

    For PCB repairs, the optimal glue choice depends on:

    Bonding Material– Plastic, metal, and ceramic each have compatible adhesives. Know the composition of surfaces involved.

    Cure Conditions – Some glues require heat, mixing, humidity control, or UV light to cure properly. Ensure a suitable repair environment.

    Bond Strength – Repairs undergo vibration, thermal cycling, mechanical stresses. Adhesive must withstand forces involved.

    Chemical Resistance – Will repair be exposed to solvents, acids, or fuels? Glue must retain integrity.

    Insulation – Avoid conductive glues to prevent short circuiting tightly spaced tracks or joints.

    With these factors in mind, epoxy, silicone, and purpose-made PCB repair adhesives are good broad material choices for durable PCB repairs able to withstand environmental conditions.

    Will Hot Glue Damage a Circuit Board?

    Hot melt glue applied appropriately does not intrinsically damage printed circuit boards. However, there are some precautions to prevent issues:

    ●Allow recently applied hot melt to fully cool before energizing PCB. Hot glue remains slightly conductive until completely set. Slow cooling helps.

    ●Avoid heating the board excessively during glue application. Some components and coatings can be heat sensitive.

    ●Prevent hot melt seepage onto unintended areas of PCB by precisely dispensing small amounts only on target surfaces.

    ●Remove any stringy messes of cooled hot glue deposits. They could inadvertently bridge solder joints or conductive components.

    With controlled application and sufficient cooling, hot melt glues pose no risks beyond other adhesives. Their fast tacking makes them ideal for temporary PCB holding.

    How do you Glue Broken PCBs?

    How do you Glue Broken PCBs
    How do you Glue Broken PCBs

    For gluing broken PCB sections, follow good adhesion practices:

    ●Wipe away dirt and debris using isopropyl alcohol to maximize clean surface area for bonding.

    ●If needed, abrade glossy surfaces with fine sandpaper to improve adhesive grip. Avoid abrading traces or pads.

    ●Clamp or weight joints to press materials firmly together as the glue sets for optimal strength.

    ●Catalyze slow-curing glues with modest heat to accelerate repair times. Avoid excess temperatures.

    ●For larger gaps, use higher viscosity glue or gap filling compounds to fully seal spaces.

    ●Ensure full cure before stressing repairs. Check manufacturer guidance for minimum cure times.

    How to Remove PCB Glue?

    There are several effective methods for removing PCB glue:

    ●Cut away the bulk of large glue deposits using a sharp precision knife. Avoid damaging boards.

    ●Gently pry off accessible glue chunks using a plastic spudger tool once any mechanical bonds are detached.

    ●Softening hot melt and UV cure adhesives with directed heat allows prying off more easily when reworking.

    ●Slowly dissolve epoxy or cyanoacrylate using a chemical stripper formulated to attack the adhesive. Test for component compatibility first.

    ●Scrape away softened glue residues using wooden sticks, being careful to prevent board scratches.

    ●Clean any remaining film using cotton swabs soaked in stripping agents or solvents able to dissolve the glue. Check compatibility.

    With the right glue removal products and techniques tailored to the specific adhesive used, unwanted PCB glue deposits can be eliminated without damaging boards or components.

    Kesimpulan

    PCB glues like epoxy, silicone, acrylic, and hot melt provide robust, electrically insulating bonds between components and substrates during fabrication, repair, and rework.

    Selecting the best match for the materials, operating conditions, assembly methods, and economic factors at hand results in bonds with the right strength, insulating capability, and durability characteristics.

    With care and proper processes, even set adhesives can be removed. Understanding available PCB glue options enables creating optimized bonds while avoiding pitfalls like shorts or heat damage.

    FAQ-tentang PCB

    Lem PCB mengacu pada perekat yang diformulasikan untuk merekatkan komponen dan bahan secara permanen atau sementara ke papan sirkuit tercetak. Lem ini menggantikan atau menambah penyolderan tradisional untuk memasang komponen SMD seperti kapasitor, konektor, dan sirkuit terpadu ke substrat PCB.

    • Cyanoacrylate
    • Epoksi
    • Silikon
    • Lem Panas Meleleh
    • Perekat Penyembuhan UV

    For PCB repairs, the optimal glue choice depends on:

    • Bonding Material
    • Cure Conditions
    • Bond Strength
    • Chemical Resistance
    • Insulation
    Posting Terkait

    Posting Terkait

    Papan Impedansi PCB - Semua yang Perlu Anda Ketahui

    Papan Impedansi PCB - Semua yang Perlu Anda Ketahui

    Papan impedansi PCB adalah tulang punggung sistem elektronik berkinerja tinggi, di mana integritas sinyal menjadi yang tertinggi. Papan sirkuit tercetak khusus ini dirancang dan dibuat dengan cermat ...
    Cara memasang resistor pada papan sirkuit tercetak

    Bagaimana cara memasang resistor pada papan sirkuit tercetak?

    Penerapan resistor pada Papan Sirkuit Cetak (PCB) merupakan aspek penting dalam desain sirkuit. Resistor adalah komponen yang digunakan untuk membatasi ...
    Membongkar Perakitan PCB SMT - Teknologi Pemasangan Permukaan

    Membongkar Perakitan PCB SMT - Teknologi Pemasangan Permukaan

    Artikel ini mengungkap apa yang mendefinisikan proses perakitan PCB SMT, mesin, struktur biaya, keunggulan dibandingkan pendahulunya, dan strategi pemilihan mitra manufaktur.
    Manufaktur PCB Konvensional vs PCB Prototipe Cepat - Perbandingan Mendetail

    Manufaktur PCB Konvensional vs PCB Prototipe Cepat - Perbandingan Mendetail

    Dalam lanskap elektronik yang terus berkembang, pembuatan papan sirkuit tercetak (PCB) merupakan aspek penting dalam pengembangan produk. Baik itu untuk konsumen ...
    IBE Electronics Menemui Anda di CES (Consumer Electronics Show) 2024

    IBE Electronics Menemui Anda di CES (Consumer Electronics Show) 2024

    Sebagai salah satu produsen ODM / OEM global dengan basis manufaktur massal, IBE mengundang Anda untuk mengunjungi Booth 2012 & 2014 dan Booth 2929 kami pada tanggal ...
    Minta Penawaran

    Tinggalkan Komentar

    Alamat email Anda tidak akan dipublikasikan. Ruas yang wajib ditandai *

    id_IDIndonesian
    Gulir ke Atas